Skip to main content

Machine Vision Inspection Scheme for Round Hardware Fittings

Machine Vision Inspection Scheme for Round Hardware Parts Shenzhen SPOTECK Technology Co., Ltd.

SPOTECK has been focusing on machine vision inspection for 13 years. It has a wide range of applications and many detection schemes.

1. Contents and requirements of testing
Measure workpiece area:
Detection of Cylindrical Samples with Integral Height of 4*2.5mm
Content of detection:
1: Bottom detection of edge notches, holes and diameters
2: Total Height of Side Detection
3: Top test diameter, with or without holes
Note: The above detection items need to be clearly visible under the image to detect.
visual inspection machine manufacturer | automated optical inspection machine manufacturers | Sipotek Visual Inspection Machine

Coupon code: “freeshipping” on any order from sipotek.net

Detection efficiency: 200-400 pieces per minute (according to sample feeding speed).
Division of work: Subdivide the detection steps according to the detection content.
II. Equipment Composition and Major Institutions
Overall Composition: Dimension: 900*800*1850 mm
Model: SP_302C
1:SPOTECK Visual Detection Software
2: industrial computer
3: display 19 inches
4: Industrial cameras: 3 sets, bottom and top detection diameter, with or without holes, edge incisions. Side detection height
5: Industrial Lens: 3 FA Industrial Cameras
6: professional glass tray
7: solenoid valve
8: reducer
9: vibration cabinet
10: Feeding equipment (Vibrating disc, Direct Vibration, Controller).
II.1: 3-D Stereogram of Equipment Appearance
3:1 Bottom Detection Method
Bottom detection effect original picture:

3:1 Bottom Detection Method
Bottom Test Fine Product Analysis Chart: OK

3:1 Bottom Detection Method
Bottom detection edge incision defect analysis chart:NG

3:1 Bottom Detection Method
Bottom Inspection Inner Hole Excessive Bad Product Analysis Chart:NG

3:1 Bottom Detection Method
Bottom defective product analysis chart: NG

3:2 Side Detection Method
Analysis Chart of Fine Products for Side Detection: OK

3:2 Side Detection Method
Analysis Chart of Highly Bad Products for Side Detection: NG

3:3 Top Detection Method
Top test product analysis chart: OK

IV. System Installation Requirements:
Inspection space for equipment placement: Separately installing SP visual inspection system at the pipeline side, it is necessary to ensure that there is enough space to install the equipment.
Ambient temperature: 0-50 degrees Celsius;
Air humidity: below 90% RH;
Electronic jamming: Provide equipment with less electronic jamming.
Power supply: 220V, 50Hz AC, less than 1KVA power consumption
Labels:

Comments

Post a Comment

Popular posts from this blog

Automatic inspection machine for a small coin sized component made of Zamak raw material

visual inspection machine Sipotek has focused on vision  automatic inspection machine  industry for more than 16 years. Here share a  vision inspection solution  of auto component dimension and plating defects. Hello, I’m looking for an automatic inspection machine which will be used for automatic sorting of good parts and bad parts. mostly I need it for checking the dimensions and  plating defects  in my component. my component is coin shaped of size diameter – 15 mm and thickness 3 mm. material is Zamak. my monthly production is 6 million parts. I need to inspect them. regards, Shashin Our reply as below: Dear Shashin, Hope this email finds you well. I am Kathy from Sipotek, I want to recommend our high speed  vision inspection machine  to you which can measure dimension and detect products appearance defects. We are the optical visual  inspection machine manufacturer  with more than 16 year...
Post a Comment
Read more

Which products are suitable for appearance screening?

In recent years, industrial production has gradually become intelligent, and the appearance screening machine has gradually replaced the manual detection work, which not only improves the production efficiency of manufacturers, but also ensures the accuracy of product screening. So, which products are suitable for the appearance screening machine? Next, has been committed to the development and manufacture of image technology and machine vision, to provide manufacturers with appearance screening machine, precision detection equipment, automatic detection equipment for die-cutting products, and other machines – Sputek to answer for you! uuuuuuuuuu Appearance screening machine is a fully automatic optical detection and screening instrument developed on the basis of image detection technology system. It is suitable for mass production of products or spare parts in plastic, hardware, electronics, food, automobile, electrical appliances, building materials, ceramics, sanitary ware...
1 comment
Read more

Jasonmould tells you how to select plastic mold suppliers matching with yourself

When you search for “Plastic Mold Manufacturer” or “Plastic Mold Factory” on Google, you will get a lot of information and contact information about the mould manufacturers. How can you find a suitable supplier in this huge information? JasonMould recommends you send RFQ to five or more suppliers of plastic molds. Then you can compare the prices of suppliers, their reaction speed and their professional level. Usually, the plastic mold manufacturer will arrange engineers or salesmen with engineering background to contact you, which will be much better than sales without any engineering experience. Because die making is a customized and professional service, mold making experience will help to communicate and avoid misunderstandings in engineering manufacturing. It will save a lot of time and cost. When you decide to cooperate with a plastic mold manufacturer, you are advised to go to the factory for a field visit to see how their factory strength is and talk to them face to...
Post a Comment
Read more